Guest viewing limit reached
  • You have reached the maximum number of guest views allowed
  • Please register below to remove this limitation

Warming gear?

holding the vial in your hand should suffice.
 
Placing the vial right side up in hot water.
 
Just man up and pin it cold! :D

When I would warm the test I would just run the vial or syringe under warm water for a minute.
 
I don't agree with water. There might be a bad crimp on your vial, and bacteria could be introduced to your gear. I go cold, but if I did warm it I'd use a hair dryer.
 
druller655321 said:
I don't agree with water. There might be a bad crimp on your vial, and bacteria could be introduced to your gear. I go cold, but if I did warm it I'd use a hair dryer.
Click to expand...

Thats the reason you never allow the water to touch the crimp.
 
Life happens sometimes ie minute droplets splashing up or just potentially fuarking up and dropping it in the water. I guess the hair dryer could add bacteria if there's a bad seal. Just my personal preference.
 
^^way over thinking.... To each his own.
 
I put my test in a pan and put the burner on the lowest setting and heat it that way... I used to use warm water but then I had to dry all the water off before cleaning the stopper and it took longer.
 
Thanks guys I appreciate it,when I pin it cold it takes days to move I pinned Wednesday without heating and it still feels rock hard around the pin hole area .......and hurts like hell !!!how long does it take gear to move ?????
 
tommy j said:
Thanks guys I appreciate it,when I pin it cold it takes days to move I pinned Wednesday without heating and it still feels rock hard around the pin hole area .......and hurts like hell !!!how long does it take gear to move ?????
Click to expand...

Where do you pin?

Sent from my super duper VS920 4G using Am.com app!
 
The only places I know of that give you that response is calves, biceps and pecs. Pecs are quite uncomfortable, but they give you two extra parts to pin so I still do them. Trying to get 8 spots down myself. I figure once you have 8 if you need more than you need to reassess what you are doing.
 
I pin in my deltoid,tried pinning my glute in my first cycle but it was way to uncomfortable for work and training!!
 
I am only new to this it's my second cycle so I don't even have pecks gerbil lol...but again very good advice thanks man,I'm gonna try heat it with the bottle upright as you said and see how it goes .
 
All good options: hairdryer, microwave, clutch in fist, and warm water.

You should at least have 2-3 sites down for your first run, i always recommend delt and quad as they are probably the easiest and big muscle groups help. Glute is typically nice and easy, especially if you have someone to pin for you as it's awkward. After that it's up to you to find what other sites you're comfortable with. I know guys that love bicep, and others that can't pin it. Or guys who pin chest, while others get nauseous just thinking about it lol.
 
Rhadam said:
All good options: hairdryer, microwave, clutch in fist, and warm water.

You should at least have 2-3 sites down for your first run, i always recommend delt and quad as they are probably the easiest and big muscle groups help. Glute is typically nice and easy, especially if you have someone to pin for you as it's awkward. After that it's up to you to find what other sites you're comfortable with. I know guys that love bicep, and others that can't pin it. Or guys who pin chest, while others get nauseous just thinking about it lol.
Click to expand...

Thanks man I appreciate the help ,you make it sound so easy lol ..
 
Glutes quads and delts are the ones I would recommend to try, pecs are painful but doable. I might try biceps later but not in the next week or two.
 
tommy j said:
Thanks guys I appreciate it,when I pin it cold it takes days to move I pinned Wednesday without heating and it still feels rock hard around the pin hole area .......and hurts like hell !!!how long does it take gear to move ?????
Click to expand...

If it's hurts that much is not normal. Your concentration is wack in your gear, prob way too much BA. Get some grapeseed oil and cut that sheeit down. Then it wont hurt and you dont have to warm it up.
 
vassille said:
If it's hurts that much is not normal. Your concentration is wack in your gear, prob way too much BA. Get some grapeseed oil and cut that sheeit down. Then it wont hurt and you dont have to warm it up.
Click to expand...

How much grapeseed oil do I need to cut it with and how do I do it ??
 
tommy j said:
How much grapeseed oil do I need to cut it with and how do I do it ??
Click to expand...

If you double the entire content of the bottle for example then you dilute the concentration in half. That means you need another bottle as well.
So, let's say you have t400, after this it will be 200mg/ml.
Or if it;s 300 then will end up 150. You can put whatever amount of oil you want just do the math.
You can use less oil just do the math the same way.
First you need a .22 micron filter for the oil. Then bake it at 25min at 250 deg oven. I know it's a process but it beats the pain.
 
You must log in or register to reply here.
Back
Top