Guest viewing limit reached
  • You have reached the maximum number of guest views allowed
  • Please register below to remove this limitation

2ml Vials Destroying Slin Needle

MadStax

MadStax

Active member
Is there a trick to the 2ml Vials? I have to push so hard to get through the stopper, that the needle gets bent and rips through the skin, requiring a lot of force! It's not pleasant. Lol
 
MadStax said:
Is there a trick to the 2ml Vials? I have to push so hard to get through the stopper, that the needle gets bent and rips through the skin, requiring a lot of force! It's not pleasant. Lol
Click to expand...
I've used all kinds of 3 ml vials with growth and peptides and never had this problem. Are they growth vials? Thinking you may have to swap needles, drawing and pinning with different ones.
 
Rebuild said:
I've used all kinds of 3 ml vials with growth and peptides and never had this problem. Are they growth vials? Thinking you may have to swap needles, drawing and pinning with different ones.
Click to expand...

Yeah, the Chinese HGH vials. I'll try to find some luer lock slin needles. Otherwise, I'm guessing I'll have to use a pen instead of syringes?
 
Humbl3 said:
Draw with a 25g and inject with the slin
Click to expand...

The slin syringes I have are with the needle built in. I have 23g luer needles and 1ml syringes, but poking a hole that big twice a day isn't appealing. I ordered some 30g 1/2" luer needles to inject with. I'll make the slin pin work til then. Just wanted to be sure there wasn't a trick I didn't know about. Thanks! 😀
 
MadStax said:
The slin syringes I have are with the needle built in. I have 23g luer needles and 1ml syringes, but poking a hole that big twice a day isn't appealing. I ordered some 30g 1/2" luer needles to inject with. I'll make the slin pin work til then. Just wanted to be sure there wasn't a trick I didn't know about. Thanks! 😀
Click to expand...

Yeah, the ones with the needle built in suck. The trick is to use the luer lock ones and swap them out as you've described.
 
MadStax said:
I pulled the plunger out of the slin pin and when I squirted the HGH in, most of it dripped out before I could put the plunger back.
Click to expand...

if you have any regular luer lock syringes, draw up all the GH at once. Get however many syringes you need ready. Take the drawing needle off and pull it into the slin pin from the top of the drawing syringe.
 
MadStax said:
I pulled the plunger out of the slin pin and when I squirted the HGH in, most of it dripped out before I could put the plunger back.
Click to expand...
Video yourself doing this. I’ve backloaded pins a ton and have never seen this. Maybe I am misunderstanding
 
trumac said:
Video yourself doing this. I’ve backloaded pins a ton and have never seen this. Maybe I am misunderstanding
Click to expand...

This method works great with oil, but the water runs right through into the cap before you can get the plunger in the back end.
 
trumac said:
Would 29 ga slin pins maybe work better/not bend as easy? Assuming you are using 30
Click to expand...

I'm using a 29g. I've never had one bend in a 10ml or 30ml vial. The 2ml vials have very thick tops! Like, insanely thick and hard!
 
MadStax said:
I'm using a 29g. I've never had one bend in a 10ml or 30ml vial. The 2ml vials have very thick tops! Like, insanely thick and hard!
Click to expand...

I hate to have to ask this (but I must)....
Are you sure you aren't poking through a (non-metal) cap?
 
... I've see a lot of stuff over the years.
... Stuff like this really happens
 
So I was just thinking. With my gh I have to get it right in the center or the caps are quite thick. Are you just hitting the sides? I’ve done it with my gh and had to pull back and try again
 
trumac said:
So I was just thinking. With my gh I have to get it right in the center or the caps are quite thick. Are you just hitting the sides? I’ve done it with my gh and had to pull back and try again
Click to expand...

Yeah, if I miss the center, it's all over for sure! The center is still quite thick though and definitely blunts the point of the pin. It doesn't slide into the skin, it must be forced through.
 
MadStax said:
Yeah, if I miss the center, it's all over for sure! The center is still quite thick though and definitely blunts the point of the pin. It doesn't slide into the skin, it must be forced through.
Click to expand...

That uhhh .....

.... that's what she said.
 
You must log in or register to reply here.
Back
Top