Guest viewing is limited

Looking to salvage some crystallized Test E

EVILADAMS

EVILADAMS

Member
Here is the low down;

Just got it in the mail today. 10mls, 250/ml, and it looks like slushy :damnit1:. Is it a total loss or is there a way to correct this and make it useful?

Thanks fellas.
 
Reheating is always plausable ... but chances are your going to need to add a little bit more solvent (BA or BB). The test has just fallen out of solution. You should be able to salavage it.

Thanks,
Sprt
 
EVILADAMS said:
Here is the low down;

Just got it in the mail today. 10mls, 250/ml, and it looks like slushy :damnit1:. Is it a total loss or is there a way to correct this and make it useful?

Thanks fellas.
Click to expand...

I'd contant the source and ask them to send another bottle. That shouldnt be a problem if our source is legit. If he's reliable, he even let you keep the slushy. lol, :0)

Sprt
 
I could probably send it back for an exchange, but I don't have my receipt!:joke:

If I was to do it myself I would have to run it through a filter again wouldn't I? I wouldn't know how much BA or BB to add to a 10 ml amp. I obviously would lose potency but thats not a big deal to me.
 
crashed out of solution, it should go back into solution if you reheat it. There's a few methods... I've heard of putting a needle in the top for vent and putting it in the oven for like 15 minutes (probably low temp like 250f). Might also be able to do something simple like microwave up some water real hot and toss the vial in.

Ideally it'll redissolve and stay in there. If it doesn't then you'll need something like BA to help it stay dissolved
 
Ya, like he said.

First try a water bath ... boil a small pot of water, once boiling turn the heat off and let your 10ml vial sit in it until it redisolved. It might hold, it might not. If nothing else, just reheat before each injection if you see crystals.

Sprt
 
UnrealMachine said:
crashed out of solution, it should go back into solution if you reheat it. There's a few methods... I've heard of putting a needle in the top for vent and putting it in the oven for like 15 minutes (probably low temp like 250f). Might also be able to do something simple like microwave up some water real hot and toss the vial in.

Ideally it'll redissolve and stay in there. If it doesn't then you'll need something like BA to help it stay dissolved
Click to expand...


Unreal, whats up brotha. Yeah crashed like a NASCAR. I'll give it a whirl. I should just start making my own.

SprtNvolcoM said:
Ya, like he said.

First try a water bath ... boil a small pot of water, once boiling turn the heat off and let your 10ml vial sit in it until it redisolved. It might hold, it might not. If nothing else, just reheat before each injection if you see crystals.

Sprt
Click to expand...

Thanks dude. Presumeably it would recrystallize in my glute then, would it not? I've never dealt with crystallized gear.
 
Whats the concentration? The water idea is the easiest. Just let it sit in the almost boiling water. You could also buy some sterile oil with solvent and cut it down in a new vial after heating if it crashes again.
 
EVILADAMS said:
Thanks dude. Presumeably it would recrystallize in my glute then, would it not? I've never dealt with crystallized gear.
Click to expand...

You'll be fine ... the reheat should take care of the problem. If not, it's not going hurt you to reheat (warm rather) each time you inject. After each reheat it should stay in solution for several days before showing signs of another crash; that is if it even ends up crashing again. I'vehad gear stay in solutions for monhs before falling out again after a reheat. The solution is just lacking the right amount of solvent - which is causing the crash.

As mentioned, however, if you dont feel comfortable reheating each time you inject you'll have to add more solvent. Or send it back. Those are your only choices.

Sprt
 
Its looking like I will just exchange it for a new one. Hopefully this isn't a recurring problem.

And yes I would definitely vent if I baked or boiled.
 
Smiley said:
Whats the concentration? The water idea is the easiest. Just let it sit in the almost boiling water. You could also buy some sterile oil with solvent and cut it down in a new vial after heating if it crashes again.
Click to expand...


250mg/ml, 10ml amp. Slushy, very slushy.
 
EVILADAMS said:
Its looking like I will just exchange it for a new one. Hopefully this isn't a recurring problem.

And yes I would definitely vent if I baked or boiled.
Click to expand...

DO NOT BAKE!!! You run the risk of melting either the plastic on the needle or the rubber stopper; believe me I know from experience. Also, venting is not necessary when using a short warm water bath.

Sprt
 
SprtNvolcoM said:
DO NOT BAKE!!! You run the risk of melting either the plastic on the needle or the rubber stopper; believe me I know from experience. Also, venting is not necessary when using a short warm water bath.

Sprt
Click to expand...


Sent it back dude. Should have a new one early next week. The source is cool.
 
SprtNvolcoM said:
DO NOT BAKE!!! You run the risk of melting either the plastic on the needle or the rubber stopper; believe me I know from experience. Also, venting is not necessary when using a short warm water bath.

Sprt
Click to expand...

I've read to bake at a low temp, I am guessing in the 200-250F range, just above the boiling point of water probably... at this point the plastic shouldn't melt... How hot did you bake for the rubber/plastic to melt?
 
I think your oven temp is off, cause im sure gear has gotten hotter than that sitting in my car in the hot Texas sun during the summer.
 
You must log in or register to reply here.
Back
Top