Guest viewing is limited

Need some help bros please answer...

bullfx

New member
Sorry i knwo this will be a dumb question but please answer it..

I am tryin to inject my IGF1 IM using a 1/2 cc Slin pin, how do i do it? the slin pin is so small it wouldnt be goin deep enough in the muscle Or even SubQ ( its only like 1.5cm long) so how can i go about doin this?

i cant change the pin either on the 1/2cc slin pins they com wiht a pin already... I do have 1cc slin pins also on those i can chang the needle but they are harder to measure 40mcg ...

if my btl is 1000mcg/ml , on a 1/2 cc slin each line would be 10mcg and on a 1cc would be 20mcg correct?

thanks for your time in advance...
 
Dosage questions have been asked an answered so many times already. Please use the search function.

ManBeast
 
ManBeast said:
Dosage questions have been asked an answered so many times already. Please use the search function.

ManBeast
Click to expand...


i have done that bro... Ok ignor that question, what bou tth einjection one?
 
Inject into a muscle that does not have very much fat over it. Like bi's, tri's, delts, outer quads, pec, or calf. This isn't something that needs to go deep IM. As long as it gets into the muscle. If your having problems with that just use it Sub-Q.
 
bullfx said:
Sorry i knwo this will be a dumb question but please answer it..

I am tryin to inject my IGF1 IM using a 1/2 cc Slin pin, how do i do it? the slin pin is so small it wouldnt be goin deep enough in the muscle Or even SubQ ( its only like 1.5cm long) so how can i go about doin this?

i cant change the pin either on the 1/2cc slin pins they com wiht a pin already... I do have 1cc slin pins also on those i can chang the needle but they are harder to measure 40mcg ...

if my btl is 1000mcg/ml , on a 1/2 cc slin each line would be 10mcg and on a 1cc would be 20mcg correct?

thanks for your time in advance...
Click to expand...
........as for the injection question........delts, pecs, calves all have low BF levels and will easily go Intra-Muscular injection. Sub-cutaneous injections with IGF leave welts/lumps for many days. I felt the Pecs were easiest and least painful site to inject. As with any injection, use proper procedures, i.e., avoid veins and aspirate (if you don't know, search or don't use any compounds until you further educate yourself)

For dosing, read every thread in the IGF section, you will not only learn more but undoubtedly find the information on dosing you are looking for, I know because I have posted it before as have many others on the board. Education my friend will serve you well in this arena.
 
check this link out, this is but one example of someone not educating themselves prior to indulging in LR3IGF1, a very costly mistake.

Invalid Link Removed
 
Sup Bro, not sure how you slin pin is marked, so here and easy brake down. The 10 unit mark is 100mcg, each unit is 10mcg. I used a half inch pin with no problems as mentioned it doesn't have to be deep like AAS

JohnnyB
 
I'll add my little tidbit. Easiest way to do sub-q injects is the pinch the skin around your obliques then inject. Those who get welts/lumps are most likely injecting into adipose tissue. If you do this right, you will not get any lumps/welts at all.
 
thanks for ur input guys... i am just really used to deep injections. it just looked like the pin is way too short..

cheers
 
gobig1 said:
check this link out, this is but one example of someone not educating themselves prior to indulging in LR3IGF1, a very costly mistake.

Invalid Link Removed
Click to expand...

ya bro i have already seen that.. :)
 
You must log in or register to reply here.
Back
Top