clomid powder

rebo

New member
have 1 gram of clomiphen powder,does this have to be suspendid,or is there a way to just measure out powder and take it with juice.Any help would be greatly appreciated im new to the liquid,powder pct.
 
If you have a scale, you can measure it, but it would be a pain. Otherwise, dump all 3 grams in 50ml of solution and it will give you a nice research dose of 60mg per ml.
 
What solutions can be used other than pga.(and i dont mind having to shake it) would water work?
 
Im not that knowledgable on Homebrewing yet... (Working on it), but I think you should at least us Olive Oil.

Adams
 
Water will work fine if you do not mind shaking, at least it does at 20mg/ml. I have not tried a higher concentration, so you may have to dilute it more.
 
I figured if water would work, then an alcohol would. I tried mine at 50mg/ml in around 90 proof rum. It went into the solution perfectly, but after about 2 days it fell out and got extremely clumpy. Now, I have to give it a hot water bath most of the time and it goes right back in the solution. I will try PEG400 next time.

custom said:
Water will work fine if you do not mind shaking, at least it does at 20mg/ml. I have not tried a higher concentration, so you may have to dilute it more.
Click to expand...
 
Well, as of last night, I wasted about half of 3 grams of clomid powder I had. Like I said in my last post, I tried alchol, 60ml for 3 grams. That should have been 50mg per ml. Anyway, all went well, but last night I opened up the bottle I have it in and it completely caked up. It looked as if there was almost no alcohol left, just a white goop at the bottom. Tried to get it out with no success. Oh well, I still have 6 grams. I will try PEG400 next time.
 
Why don't you pour that goop in a graduated cylinder, use little bits of alcohol to swish around in the bottle and get it cleaned out, pour this in the cylinder each time till you have like 50ml or so in the cylinder. Put this back in your container.

Pour another 12ml in the cylinder and swich it around to get everyhing in the cylinder into the liquid, and pour that back into the container too. This should let you accurately measure how much solution you have currently, get it back to your original concentration, and not waste any of your valuable research material!

I hope that is understandable, I see the procedure in my head but can't really describe it. I am pretty sure your goop will disolve.

If it takes additional alcohol to get the goop out don't worry, you can evaporate it off.

HOpe that helps and good luck!

If the alcohol just evaporated I don't think the clomid would have gone bad.
 
It was only 9.99 for the 3 grams of clomid. I thought about doing all of that, but I don't like NOT knowing if I am getting a correct dosage of something. I didn't know how much powder was actually left in the bottom and don't have a scale. I was a little pissed to and just filled it with water and poured it out.

cr4ytonic said:
Why don't you pour that goop in a graduated cylinder, use little bits of alcohol to swish around in the bottle and get it cleaned out, pour this in the cylinder each time till you have like 50ml or so in the cylinder. Put this back in your container.

Pour another 12ml in the cylinder and swich it around to get everyhing in the cylinder into the liquid, and pour that back into the container too. This should let you accurately measure how much solution you have currently, get it back to your original concentration, and not waste any of your valuable research material!

I hope that is understandable, I see the procedure in my head but can't really describe it. I am pretty sure your goop will disolve.

If it takes additional alcohol to get the goop out don't worry, you can evaporate it off.

HOpe that helps and good luck!

If the alcohol just evaporated I don't think the clomid would have gone bad.
Click to expand...
 
Try using a small mixer in accordance with whatever solvent you use. A little blending will do wonders. ;)
 
You must log in or register to reply here.
Back
Top