IGF-1 pinning

Tom 185

Well-known member
About to give my first IGF-1 run a go. I will be starting on the last day of my test enanthate injection. Injection schedule will be as follows:

M- chest
T-
W- calves
R-
F- bis
Sa-
Sn-

I will do 20mcg bi-laterally for 6-8 weeks and then take 4 weeks off.


Questions....

1) Can i add a 4th day weekly here to pin my biceps 2x per week or is 1x per week more efficient?

2) When pinning, should i fill the syringe to 40mcg and then inject 20 and 20 (using necessary sanitary precautions) or should i use two separate syringes at 20mcg

3) I also have BW but wasn't planning on using it unless pinning without it was really a problem...should i add it regardless?

4) In grunts take on IGF-1...he recommends 20mcg bi-laterally, but 30mcg for quads since they are bigger. Could i use this protocol for chest (since it is a much bigger muscle than bis & calves) and do 30mcg for better results?
 
Tom 185 said:
About to give my first IGF-1 run a go. I will be starting on the last day of my test enanthate injection. Injection schedule will be as follows:

M- chest
T-
W- calves
R-
F- bis
Sa-
Sn-

I will do 20mcg bi-laterally for 6-8 weeks and then take 4 weeks off.


Questions....

1) Can i add a 4th day weekly here to pin my biceps 2x per week or is 1x per week more efficient?

2) When pinning, should i fill the syringe to 40mcg and then inject 20 and 20 (using necessary sanitary precautions) or should i use two separate syringes at 20mcg

3) I also have BW but wasn't planning on using it unless pinning without it was really a problem...should i add it regardless?

4) In grunts take on IGF-1...he recommends 20mcg bi-laterally, but 30mcg for quads since they are bigger. Could i use this protocol for chest (since it is a much bigger muscle than bis & calves) and do 30mcg for better results?
Click to expand...

the whole point behind the bw is to ensure that nothing is left in the syringe,also to take the sting from the aa.....I have read alot on this,from what i gather(including myself)just use 1 syringe....use alcohol prep pads before shots tho......Grunts sticky is ony of the best reads on igf
 
you also just want to hit the bi's once a week due to downregulation. You will see once a week is really good enough. If you want to bump the dosage up on the bigger muscle go for it, it won't hurt but i really don't think it is necessary. Igf is real good. I never went above 20mcg bi lat. no matter what muscle and had good results..
 
Alright well thank you both.

should I draw the BW first or the IGF-1? I've seen it argued both ways...

Jonesboy...what do you weigh?
 
when back-loading bac water or b-12 or whatever and shooting bilaterally you are going to need two pins. if you use only one pin you will get i shot that has all the igf, and another that has the other stuff.

i recomend the methyl b-12. just pull .1 cc into the slin pin and then draw your igf. this amount will ensure that no igf is left in the pin.
 
I dissagree with that method. You always want to pull your IGF first. That way there is no chance the IGF in the vial gets contaminated.

Also, it mixes quite well in the pin (you can see this with the MB12 especially, the red color shows how the clear IGF mixes) 1 pin for a bi-lateral shot works. Only reason 2 pins would be better would be for sterility and sharpness of the pin.

Also, I pull to the .4cc mark on a .5cc slin pin and shoot .2cc bi-lateraly. Anything left in the pin is quite negligible.
 
hmmm. i guess if you are pulling that much it will mix. when i do the smaller amount it always stays in front. i'd still be concerned about how evenly it is dispersed, but that is just me.
 
RedwolfWV said:
I dissagree with that method. You always want to pull your IGF first. That way there is no chance the IGF in the vial gets contaminated.

Also, it mixes quite well in the pin (you can see this with the MB12 especially, the red color shows how the clear IGF mixes) 1 pin for a bi-lateral shot works. Only reason 2 pins would be better would be for sterility and sharpness of the pin.

Also, I pull to the .4cc mark on a .5cc slin pin and shoot .2cc bi-lateraly. Anything left in the pin is quite negligible.
Click to expand...

so is the other .1cc your BW?
 
The brand of IGF I use is not reconstituted with AA, so no BW is needed (although if I don't have methylB12, I use BW)
 
I am a visual learner, is there any website that show's how to properly load the needle. Also why is better to use the MB12 over BW?

Also if I inject 3 times a week mon,wed,fri. and I workout

Chest on Monday
Bi's-Tri's on Wed
Shoulders on Friday

Should the next week I switch to hit Back on Tuesday, and Legs on Saturday? Basically should I be injecting into all the different muscle groups first, hams, calves, traps, etc... before pinning another muscle group twice.
 
You must log in or register to reply here.
Back
Top