Tren Acetate Homebrew BA/BB concentrations...

kbear

Board Supporter
So i decided to finally stop doing research conversions from kits and start using bulk chemicals and supplies instead.

Everything seems simply enough (esp. following Skye's popular post to this end), but all the instructions I have found refer only to how to make Tren Acetate from kits, using the 'magic [BA/BB] solution".

my only question is this--

What concentration of BA and BB should I use in my solution for Tren Acetate (@100mg/ml)?

The only amount I have hear before referenced for Trenbolone Acetate is 4%BA and 12%BB (this was, however, at 75mg/ml).

Is a 4% BA, 12% BB concentration sufficient? Help!

Thanks all!
 
kbear said:
So i decided to finally stop doing research conversions from kits and start using bulk chemicals and supplies instead.

Everything seems simply enough (esp. following Skye's popular post to this end), but all the instructions I have found refer only to how to make Tren Acetate from kits, using the 'magic [BA/BB] solution".

my only question is this--

What concentration of BA and BB should I use in my solution for Tren Acetate (@100mg/ml)?

The only amount I have hear before referenced for Trenbolone Acetate is 4%BA and 12%BB (this was, however, at 75mg/ml).

Is a 4% BA, 12% BB concentration sufficient? Help!

Thanks all!
Click to expand...
tren ace can go to 200mg/ml with 3% BA and 12%BB. that dose bother some people so 100mg/ml is fine with the same.
 
Skye said:
tren ace can go to 200mg/ml with 3% BA and 12%BB. that dose bother some people so 100mg/ml is fine with the same.
Click to expand...

Thank you both Skye and Klaus.

I think I will go with 3%/ 12% @100mg/mL.

Just out of curiousity's sake, does anyone know what the concentration of these solvents normally is in the 'magic solution' contained in fina conversion kits? I am just wondering if there is any normal standard concentration or instead whether the concentration just falls within an acceptable range that varies between kit-makers.
 
kbear said:
Thank you both Skye and Klaus.

I think I will go with 3%/ 12% @100mg/mL.

Just out of curiousity's sake, does anyone know what the concentration of these solvents normally is in the 'magic solution' contained in fina conversion kits? I am just wondering if there is any normal standard concentration or instead whether the concentration just falls within an acceptable range that varies between kit-makers.
Click to expand...
it varies from kit to kit. some of the older ones (maybe still) were nothing but BA and some were a verity of solvents, one I think used glauacol as a base with some other and one used a polyhydric alcohol blend. they always seam to think that this was a big secret or something but all this was around for years.
 
200mg/ml? That doesn't hurt?

So far, I've only brewed with 2:20, figured it'll hold about everything at standard concentrations :D haha
 
2% 20% is nice and smooth as a standard. :)

but 3% 12% is good to go with Tren Ace.

more BA you add, the more bite in my experience. :D
 
I tried 100mg buy changing something in the kitchen . But now I have holes in my muscles where I IM . Have you heard of this before. I read something that said BA could eat through a table . Hows that on muscle???
 
dirtysouthmuscl said:
I tried 100mg buy changing something in the kitchen . But now I have holes in my muscles where I IM . Have you heard of this before. I read something that said BA could eat through a table . Hows that on muscle???
Click to expand...

You have "holes" in your muscle? Care to elaborate?

Or, if you can get pics, that be even better
 
I did

hey I did google it and i didn't get anything for answers. All i need to know is where could i get a kit to make the tren and the steps.
 
You must log in or register to reply here.
Back
Top