Guest viewing limit reached
  • You have reached the maximum number of guest views allowed
  • Please register below to remove this limitation

Making Test Enanthate

Kitchen Chemist

Active member
This experiment will yield 100mls of test enanthate at 250mg/ml.

Sorry bros, I forgot to take pictures of a few steps.

Things needed:

1 - 5ml syringe
1 - 10-12ml syringe
1 - 20ml syringe
A few needles 18-23g
Alcohol wipes or another way to help ensure sterility
2 sterile 100ml vials (must be identical)
5ml benzyl alcohol (BA)
1 .22-.44 pore size sterile syringe filter
25 grams testosterone enanthate powder
1 - Small funnel
Approx 75ml Sterile Oil
Pen/marker that will write on glass
Accurate scale
Rubbing alcohol
Duct tape
 
Weigh out 25 grams of test enanthate. Notice that some of the powder is hardened as it melted a bit in my pocket and then hardened in cooler temp.
 

Attachments

  • 1.jpg
    1.jpg
    17.3 KB · Views: 5,150
Take lid off of 100ml vial and fill with 100ml of rubbing alcohol using 20ml syringe. Once you have fininshed mark line where alcohol level is and dump out liquid. Put bottle in oven at 200 F and let liquid evaporate. Sorry no picture.
 
Take funnel and pour powder into vial. Add 5ml of BA using 5ml syringe and put in pot of water on low till powder has completely turned into a liquid.
 

Attachments

  • 2.jpg
    2.jpg
    13.7 KB · Views: 4,492
Take 20ml syringe and fill vial with oil until you are about a cm or so from the 100ml line you had previously marked on vial (not very accurate i know). As you can see, i duct taped the stopper on real good so that the vial can be turned upside down and not spill.
 

Attachments

  • 3.jpg
    3.jpg
    18.5 KB · Views: 4,431
Wipe rubber stopper of second 100ml vial and put two 20ga needles through it. Attach whatman filter to syringe.
 

Attachments

  • 5.jpg
    5.jpg
    26.8 KB · Views: 4,416
Repeat procedure until bottle is finished, but leave whatman filter in sterile vial, just remove syringe to refill.
 

Attachments

  • 7.jpg
    7.jpg
    32 KB · Views: 4,544
Once done with bottle, draw up 15ml or so of sterile oil. Grab empty bottle that has 100ml marking and put beside filtered bottle of gear. Flush filter with oil until the bottle matches the 100ml line of empty vial.
 

Attachments

  • 8.jpg
    8.jpg
    25.3 KB · Views: 4,398
There you have it, 100ml at 250mg/ml. May not have been the best way to do this but this was my first attempt at this and i think it turned out well. A couple of things i experienced that i should point out.
I tried using 20ml syringe but 12ml one was much faster.
I made eq the same way but filtered into 10 10ml bottles, I believe that using the 100ml vial was faster and more sterile than using 10 small bottles. Now all you have to do is draw gear up and inject 10ml into each bottle. Now go get huge!
 
It is the exact same just use 20g of eq rather than 25g to give you 200mg/ml rather than 250mg/ml. I will post up another deca and test thread within the coming week or so. This time using a powder calculator.
 
Kitchen Chemist said:
Weigh out 25 grams of test enanthate. Notice that some of the powder is hardened as it melted a bit in my pocket and then hardened in cooler temp.
Click to expand...
sorry, dont you mean 2.5g?
 
Kitchen Chemist said:
It is the exact same just use 20g of eq rather than 25g to give you 200mg/ml rather than 250mg/ml. I will post up another deca and test thread within the coming week or so. This time using a powder calculator.
Click to expand...

Would that be using boldenolone base? I ask because I have an opportunity to get some. If not, would boldenolone base be usable?

Thanks.
 
You will not get bold base at 200mg/ml unless you come up with some funky combo of solvents, ba and bb will definately not do it.

Try PEG-400, 5% BA and 15% PEG. You may have to use a glycerin with it rather than oil, but that should get it easily to 100mg/ml no prob.
 
You must log in or register to reply here.
Back
Top