Igf-1 r3

ADDEO

New member
I think I made a mistake, I hope someone can help me.
I have 2 separate 1mg vials of igf-1 r3, I mixed each with 1ml of glacial acedic acid. I then loaded my pins with 20mcg of igf and went 6 to 1 with BA.
It burned when i shot bilatterally in my bicepts post on Friday but felt killer.
Weekends are cardio so i went sub in oblique each side and it burned pretty good as well.
I guess i must be an idiot because I assumed glacial was the normal acedic acid at .6
two questions
1. Did I ruin my existing igf when I mixed with the glacial aa?
2. Can I use a higher dose of mixed BA to use it if the igf is till good.

If the Igf is good to use, if I mixed 1 ml of pure glacial acetic acid with 1 mg of IFG-1 r3 and I want to use 20mcg of ifg in a slin pin, how much bac water should I put in the pin with the ifg / acetic acid?

I am not worried about eating the igf, I just want to get it right. any help would be greatly appreciated
 
Last edited:
your IGF is fine in Glacial AA but you need to dilute it enough to not ruin muscle.

6/10 cc/ml Glacial AA and 10 cc/ml BAC water should get you 0.6 % AA.

Glacial AA is 99% pure and kills muscle.
 
WetWorks said:
your IGF is fine in Glacial AA but you need to dilute it enough to not ruin muscle.

6/10 cc/ml Glacial AA and 10 cc/ml BAC water should get you 0.6 % AA.

Glacial AA is 99% pure and kills muscle.
Click to expand...

You do not need to dilute the AA.
It will not kill your muscle.

BA will just degrade the IGF quicker.
 
For such a delicate peptide it will be interesting to see if the igf is ok. You will probably just experience discomfort upon injection.
 
So if I mixed 1 ml of pure glacial acetic acid with 1 mg of IFG-1 r3 and I want to use 20mcg of ifg in a slin pin, how much bac water should I put in the pin with the ifg / acetic acid?
 
SolidusSnake said:
You do not need to dilute the AA.
It will not kill your muscle.

BA will just degrade the IGF quicker.
Click to expand...



Acetic acid, CH3COOH, also known as ethanoic acid, is an organic acid that gives vinegar its sour taste and pungent smell. It is a weak acid, in that it is only a partially dissociated acid in an aqueous solution. Pure, water-free acetic acid (glacial acetic acid) is a colourless liquid that absorbs water from the environment (hygroscopy), and freezes at 16.5 °C (62 °F) to a colourless crystalline solid. The pure acid and its concentrated solutions are very corrosive.
 
WetWorks said:
Acetic acid, CH3COOH, also known as ethanoic acid, is an organic acid that gives vinegar its sour taste and pungent smell. It is a weak acid, in that it is only a partially dissociated acid in an aqueous solution. Pure, water-free acetic acid (glacial acetic acid) is a colourless liquid that absorbs water from the environment (hygroscopy), and freezes at 16.5 °C (62 °F) to a colourless crystalline solid. The pure acid and its concentrated solutions are very corrosive.
Click to expand...

So basically don't use the igf I mixed with the glacial, correct?
 
basically I have I have 1 vial mg of igf-1 mixed with 1 ml of glacial acetic acid. I can't dillute the vial, so because of the concentration using a .5 slin pin at 40mcg, I can't reach the correct dilluting formula. Doesn't that mean the ph will be no good and the igf is also no good to me either?
Just asking. I shot 20mcg diluted in the pin 4 parts water to 1 part igf. It burned but only for a minute.
Any ideas.
Thanks
 
ADDEO said:
basically I have I have 1 vial mg of igf-1 mixed with 1 ml of glacial acetic acid. I can't dillute the vial, so because of the concentration using a .5 slin pin at 40mcg, I can't reach the correct dilluting formula. Doesn't that mean the ph will be no good and the igf is also no good to me either?
Just asking. I shot 20mcg diluted in the pin 4 parts water to 1 part igf. It burned but only for a minute.
Any ideas.
Thanks
Click to expand...

20 mcg would be the 1st line on the slin pin if I'm not mistaken. you are probably getting it down to 10% or so. if you can get 1cc/ml slin pins it would make it better. I wouldn't get rid of the IGF if it was me.
 
If I wanted to get to .6% acetic acid from 100% pure (1ml) in my reconstituted 1 mg ifg
in a .5 slin pin. If I go 20mcg (2 tic marks) and add for my injection My BAC to the 33.3 tic mark would that constitiute the proper dilluted amount for achieving the proper .6% acid level?
20/.6=33.3 or is this just flat out wrong
I have 2 mixed vials of 1mg each with 1ml of pure glacial acteic acid.
Any help?
 
I appreciate the answer,
Help me understand:

I get the .2 instead of 20, where does the .48 come into? remaining tics on the pin? Ultimately is 9.6 the percentage based on the the total of what the .5 pin can carry as the balance of bac water used.
Breakdown:
The pin has 50 tics. 2mcg is the first tic.There are 49 tics remaining on the pin so filling the balance up with bac still leaves the content of 9.6% acetic?
 
ADDEO said:
I appreciate the answer,
Help me understand:

I get the .2 instead of 20, where does the .48 come into? remaining tics on the pin? Ultimately is 9.6 the percentage based on the the total of what the .5 pin can carry as the balance of bac water used.
Breakdown:
The pin has 50 tics. 2mcg is the first tic.There are 49 tics remaining on the pin so filling the balance up with bac still leaves the content of 9.6% acetic?
Click to expand...

true, thats why I suggested getting 1cc/ml slin pins.

I took the tics from IGF 0.2 x 0.48 remainder for BAC water. if you used 1cc/ml slin pin it would be 0.2 x 0.98 = 0.196 well within the right dilution. I would let it stay in the high AA and just draw out of both the vial and than draw out of the BAC water.
 
I appreciate the information, thank you
You are pretty confident that the 1ml Glacial at 97.7% pure didn't effect the 1mg igf?
 
ADDEO said:
I appreciate the information, thank you
You are pretty confident that the 1ml Glacial at 97.7% pure didn't effect the 1mg igf?
Click to expand...


not in a bad way. the stronger the AA the better it stores. for the future I wouldn't start with pure AA.
 
You must log in or register to reply here.
Back
Top