Guest viewing limit reached
  • You have reached the maximum number of guest views allowed
  • Please register below to remove this limitation

Crashed Tren Enth 200mg/10ml vials.

JuiceBoxJack

JuiceBoxJack

New member
Ok so I had two vials of Tren Enth 200mg/10ml vials that had decent sized crystal shards floating around which I should have spotted before taking them. Regardless I did my research and found that this doesn't mean that they're destroyed and that if anything they're legit but need to be salvaged. I guess this happens to gear that dosed with high hormones with just enough solvent or barely enough to still it. Or also because they were stored under 50 degrees. So what I did was ran them both under scorching hot water and shook them and repeated this for about twenty minutes until the crystals were completely dissolved and the solvent was clear. So to my understanding these vials of Tren should be good to go ? They've been clear for 3 days now.... Any second opinions would be great ! Thank you
 
Sounds like you're good to go brother. I usually vent my bottle with a sterile 25g and cook it on the stove at the lowest heat possible. But if the crystals are gone, you're good. I'm sure it was the low temp.
 
How do you like Tren man ? I hear so much about it, I've ran three cycles of test and dbol so far my last cycle being 750 a week for 16 weeks. I feel that I'm ready for it. What kind of roller coaster ride should I expect ? I want to be in for a ride.
 
At low doses with lower doses of test. Next time I may go against the rules altogether and Just Go With It by itself.
 
Heard so much man , I heard that's a waste of test because Tren uses up receptors but at the same time I have experienced users messaging me saying that they don't compete . I respect their opinion .
 
I don't take test past 150 a week with tren. Google "laws of trenbolone"
It's explained thoroughly with many different people chiming in with personal experiences. It's an awesome compound. It's really the effing king of gear. I heard a guy say when all the roids are sitting at the table talking, when tren starts talking, everyone else shuts their effin mouth.

When I keep test low, my tren sides are low. Run some niacin and gw501516 with it too. That'll fix the lipid issue and the lethargy/ cardio kill.
 
And also brother, I'm 40 and conservative with my doses. I'll never take tren past 250 again in my life. I also see to get more sides from ace, which is ok because I grow tired of all the jabs.
 
I pretty much live off 200mg test a week, and 3iu gh a day
 
When I get home I'll read the article , I'm out and about . Here's the deal I have 4,000mg of Tren Enth & 10,000mg of Test Sust. Never mind the D-Bol. What do you think in your personal opinion I should run the Tren to Test ratio at ? I've got plenty of AI and PCT it's not a factor.
 
bro , just get a filtered syringe tip to draw out your dose. If theres any glass or w.e in it. It will catch it.
 
You know I'm pretty sure CVS offered those to me one time but I wasn't to sure of what they were talking about . When the girl offered them to me she sounded like she had Down syndrome so I couldn't understand her completely. But let me go back and double check. Thanks for you input . Semper fi
 
stankyleg said:
Sounds like you're good to go brother. I usually vent my bottle with a sterile 25g and cook it on the stove at the lowest heat possible. But if the crystals are gone, you're good. I'm sure it was the low temp.
Click to expand...

Me too
 
Your good, sometimes you even have to do this before every shot because it constantly crashes.. rare but it has happened.
 
criticalbench said:
Your good, sometimes you even have to do this before every shot because it constantly crashes.. rare but it has happened.
Click to expand...

Yup. Either too much compound or not enough solvent.
 
JuiceBoxJack said:
I don't mind I normally warm up my vials prior to pinning just so the juice isn't as thick. Feels smoother to me .
Click to expand...
I did the same as Juicebox it does seem to help with pip and helps with crystals forming. Warm up enough water in a small cup just high enought to cover 1/3 or 1/2 of the vial... once warmed place the vial in the cup let it sit a minute or so and it should be good to go... usually in my experience it was lol
 
You must log in or register to reply here.
Back
Top