Guest viewing limit reached
  • You have reached the maximum number of guest views allowed
  • Please register below to remove this limitation

Another 1T+4ad homebrew Q

andro69

andro69

Member
Hi, this is my first post here. I've been reading alot of posts about homebrews and am just alittle confused on the different reccomendations for the different ingredients. This is what I have seen so far,
60% iso..........240- 60%=144ml
30% ipm.........240-30%=72ml
10% oa...........240-10%=24ml
Another-
40% ISO is 96ml
15% IPP is 36ml
15% IPM is 36ml
10% OA is 24ml
10% PG is 24ml
10% DMSO is 24ml
And yet another-
40% everclear
30% ipm
10% oa
10%glycerin
10% dmso.
All reccomend a 240ml. bottle.

My question is, if I wanna make a homebrew similar to 0ne+(which I'm using right now and experiencing good results) but with higher dose per ml, what combination would I mix and what would be the highest amount of 1T+4ad I could mix in? Thanks for any replys and sorry if this was already asked and I missed. Andro69
 
Ok, I just got finished with some more browsing and more specifically, wanna know if 18 grams of 1AD and 5 grams of 1T can go into 240 ml of solution without any probs. And again, what would be used to mix it with. I wanna get around 150mg of 1T and 600 of 4AD in 6 squirts which is 3 ml.
 
Well, I am fairly new here to, but from what I have read, the ingredients you have listed, are for a liquid spray and not a gel. Also, that does not include the PH. To be the same as One+, you would have to add 2.625 of 1 test and 9.375 of 4 ad. That is what is in the One +. If you want a gel I just ordered the t-gel from this site along with 1-test and 4 ad and I will be mixing them myself. I hope this helps.

Thanks

rharg
 
I read that 12g of any PH per 240mL is about the concentration you want to achieve. But I asked about putting in 10g of 4 ad and 5g of test and I was told that would be fine. Also, there is a calculator on this site that will give you all the information you are looking for I will find it and post the link.
 
Well boys..it looks like you got quite a lil discussion goin' on in here ;)

Alright then:

The MAX amount of prohormones that you want mix into 240ml of solution is 15g (10g 1-Test/5g 4-AD, 10g 4-AD/5g 1-Test...or any other combination you can think of)....any more PH and you will not be able to get it into solution, and that is not a good thing.

I personally use the following recipie:

40% Isopropyl Alcohol (99% pure)

30% IPM

10% OA

10% PG

10% DMSO

BUT it would be easier to buy the T-Gel and then add in the ratio of prohormones that you want to.

PM me if you want any more info :)

 

LG. :cool:

 
 
By the way there is no point in putting 1-ad and 1-test in the same bottle. 1-ad is the precurser to 1-test. So basically they are the same thing. So juts do the parent drug. 1-test...... If you are using that recipe it will be very liquidy... Its the recipe I use as well. Go get yourself a hairspray bottle and use that for applicating.. Works very good. Or like LG said just get the t-gel and add your own PH's.. Hope that helps.. Talk to ya
 
curt2go said:
If you are using that recipe it will be very liquidy... Its the recipe I use as well. Go get yourself a hairspray bottle and use that for applicating.. Works very good.
Click to expand...

I'm gonna have to try this next time.....I was using a mason jar to hold the mix and an oral syringe type to measure out the ml's....I'll just count how many sprays to = ml and go from there. What I am using is a bit messy, but it gets the job done.

Andro69, any of those mixes will work well...always opt for the dmso in the mix and add d-limonene (5%) for the smell and emulsification purposes.....something BDC let me in on, which helps the formula from seperating while sitting. Good luck.
EX: 40% iso
25% ipm
10% oa
10% pg
10% dmso
5% d-lim
 
You must log in or register to reply here.
Back
Top