What happened on my last injection?

whaz

whaz

Member
I've been on a Test cycle for the last month and thus far every injection has gone great. I was using Sust 250 and had gotten used to the feel of the oil and the overall process. I decided to switch to Test E and dosed 250mg Wednesday evening (.5cc). When I injected I could tell something was up. I felt a lot of resistance and then release so I'm pretty sure I went through a vein. This was outer right quad by the way. I aspirated and everything looked fine, just like normal. So I decided to proceed with the injection. After that, everything seemed normal.

Thursday, however, I woke up and my leg was incredibly sore, worse than the Sust by far. Today I can barely walk, although there is no apparent bruising.

My question - What the hell is going on?! I'm assuming that it's either the new oil or the vein that I went through, leaning more towards the vein. It's very sore from a few inches above my knee to a few inches below my hip/pants pocket area. Any guesses on when this might go away or any tips on how to help it out? I've been stretching my quad a lot and that's def helping but I don't think I could handle a foam roller, it's pretty painful.

(This is my first injectable cycle by the way)
Thanks guys!
 
Could of went through scar tissue? Also you said .5cc 250 which means 500 1cc. So it's also high concentration and with gear like that pip is normally worse
 
That's something that I hadn't considered but makes sense. I have been hitting the same general area in the quad so I might need to move around in that section a bit. Thanks for your reply.
 
Do you know the difference between the carrier oils? You may be dealing with a substance which is more viscous than the previous one. And as thyrod has said, a higher concentration of gear (500mg/ml of test e is a very high concentration) will likely cause more pip.
 
GreenEarth said:
Do you know the difference between the carrier oils? You may be dealing with a substance which is more viscous than the previous one. And as thyrod has said, a higher concentration of gear (500mg/ml of test e is a very high concentration) will likely cause more pip.
Click to expand...

I don't recall what oil the sust had but my Test E is grapeseed oil. I've been reading up on cutting the Test. I don't wanna trash it but I really don't think another shot is gonna work. I did ventroglute yesterday and I could hardly get out of bed this morning. I've been reading about cutting 1:1 with sterile grapeseed oil. Some people also mentioned B-12? You guys have any thoughts on this?
 
Sounds to me like an extremely high dose of benzoyl alcohol, I would get different gear, I have used an array of enanthate 250/1cc and cyp, and prop.. Prop should hurt the worst, I have acces to non-alcohol enanthate but its just a pain to heat it up all the time.
Did it make you sick at all?
 
Littleguy0321 said:
Sounds to me like an extremely high dose of benzoyl alcohol, I would get different gear, I have used an array of enanthate 250/1cc and cyp, and prop.. Prop should hurt the worst, I have acces to non-alcohol enanthate but its just a pain to heat it up all the time.
Did it make you sick at all?
Click to expand...

I have some 100mg/ml prop from another source that I'm going to try tomorrow and see how I react to it. I've taken three doses of this Test E and each time I've felt achy and sick the next day. I got some grapeseed oil and filters so my plan from this point is - Use the prop tomorrow and see how it goes. If all goes well then just continue with that. If the pip is equal to the Enan then I will try to cut the E and see how that goes.
 
babycakes said:
what he said^^^^^^^
I had pip because of high concentration, no pain after cutting it with GS oil
Click to expand...

That's what I like to hear! I've never cut test before so lemme lay out my plan and see if you guys have any advice - First I'll bake the GSO in a pyrex dish (Ive read so many different things on how hot and how long so I'm pretty confused) but lets say 250 degrees for 90 min. Then, using a Whatman filter I'll transfer the GSO into a sterile vial. After that I'll mix 1:1 test/GSO in a syringe when I'm ready to dose. Thoughts?
 
whaz said:
That's what I like to hear! I've never cut test before so lemme lay out my plan and see if you guys have any advice - First I'll bake the GSO in a pyrex dish (Ive read so many different things on how hot and how long so I'm pretty confused) but lets say 250 degrees for 90 min. Then, using a Whatman filter I'll transfer the GSO into a sterile vial. After that I'll mix 1:1 test/GSO in a syringe when I'm ready to dose. Thoughts?
Click to expand...
The gso you're buying should already be sterile and filtered. Just pull up a half cc of gso and a half cc of your gear. Then pin it. Next time stick with something that is either 250-300 mg/ml. High concentration gear is asking for trouble for someone new to gear.
 
You must log in or register to reply here.
Back
Top