Injection Pain

joshag

joshag

New member
Yeah I know this one has been done before and I have done the searches but I was hoping for an experienced, informed answer. I am experiencing crippling pain several hours after an injection. Very much like Test Prop. I have been pinning my quads for some time now and this has never happened. Pain can last for up to 4 days after it's pinned. Also got fever like chills for the first time in my life and they lasted for about 2 days???

Test E 250mg/ml
If I was an expert I wouldn't come seeking help but here is the deal: I am not new to gear as I have been doing it off and on for about 10 years. The gear is home brewed by me (I can see the eyes rolling already) and I am not new to this either.

This is not the first batch with this powder so I can hopefully rule that out. I have just finished a batch I made with this powder at 200mg/ml with no pain (trt).
Using a conversion calculator I used 2% BA so I don't see this as the problem. BB was also used, but again I used the same calculator I have always used.
Trying to eliminate the "human error" factor I made a second batch with very little BB and 1% BA to compare. Same result.

Any ideas?

I have been brewing at 200mg/ml for about 2 years and this is the first 250mg/ml in about 4 years back when I was using it recreationally. Could my body be having that much of a problem with the extra 50mg/ml? Can't figure it out?

Any help would be greatly appreciated.

Edit: Think I might have the answer but I need confirmation. With the increased hormone ratio I could feel the difference in the thickness of the final product. Definitely noticeable when running through a Whatman and loading a pin. Perhaps it's just the gear sitting in the muscle and not moving. No lump just pain. Again, I'm not an expert.
 
Bump this ttt, I dont think its any of the reasons you said. Fever for 2 days? is your stuff sterile? Pain for 4 days? Did you spike a nerve? Maybe someone else can chime in for you.
 
RoadBlocK said:
Bump this ttt, I dont think its any of the reasons you said. Fever for 2 days? is your stuff sterile? Pain for 4 days? Did you spike a nerve? Maybe someone else can chime in for you.
Click to expand...

I don't think sterility is an issue. Not a spiked nerve because my chances of spiking a nerve in both legs at different times is probably not possible. I have no injection site signs of infection. I have used this powder before and used the same % of BA/BB just lower concentrate of powder. I think I have too high of hormone density. I will try and cut the batch and see if it makes a difference.
 
Well, I hope you find a solution to your problem. Still wondering about the fever thing, but if you reduce or eliminate the pain, thats a good thing.
 
You body definitely would not be having a problem only stepping it up 50mg/ml.
Most pain would be because of a higher BA, and most fever(infection related) would got from something un-sterile.

Did you happen to maybe touch the needle on your fingers/clothes/skin before poking?
Also, did you swab yourself? Maybe the top of the vial could have touched something with a large amount of bacteria present?
There are so many complications that can go wrong, you should be questioning all of them :o


Also, @ your edit, i've had such thick gear, going from 3cc-vial through a .45 wattman, it took me ATLEAST 10 minutes, so i highly doubt that the gear being thick is the problem, because mine have been so thick that went i upside the vial, its still oozing its way down.

If the pain proceedes(has happened to me for 4 days) the next pin, i gave a nice massage, and put a heatpack on my leg to keep it warm and let the oil make its way around after massaging it around, and hit the sack and leave it overnight.

edit- also heard 3% BA is best
 
You must log in or register to reply here.
Back
Top