Detailed Instructions for 1-Test Cyp Powder?

Romac

Romac

New member
I have been searching and searching, and although i have pieced together much from bits and pieces of threads, i have yet to find a sticky or a detailed thread with instructions on how exactly to make an injectable solution with 1-test cyp powder, when to inject (i.e. times of day and half-life), where to get (and what type of) pins, etc.

I am going to eventually use this for my first real cycle.

My plans are:
500mg per week for 10 weeks (as i have seen suggested for noobs like myself)

I am 34 years old
183lbs@10%bf
my goals are to gain lean mass at a moderate rate, and i'm not trying to make outrageous gains overnight

please point my noob ass in the right direction :)

thanks.
 
I think many of us search for what you seek. At the moment, I am not brave enough to undertake the project. I have little faith in my ability in chemistry and have seen too many royal screwups.

But from what I understand the conversion is the same for 1-T cyp as it would be for Test cypionate.

William posted this over at bodyrecomposition. It has pictures, while most other examples don't. That is worth a lot in itself.

Invalid Link Removed
 
I suggest posting a thread or searching for info over at the injectables section, there should be some info over there. Basically from what I have researched, I would say make the concentration at 200-250mg/ml, use 5% BA and 10% BB in the solution. I am starting a cycle right now, but am using Designers 1test cyp so i didnt homebrew it. Did my first inject last night and it went very well, minor soreness today, my glutes are sorer from a hard leg workout than they are right now. I used a 25g 1.5 inch pin, and injected 1.25cc of 1test cyp and 1.25 cc of 4ad cyp in the same syringe totaling 2.5cc of total fluid injected. It went surprisingly well, no pain at all, didnt feel a thing, cranked up the Metallica and stabbed it in:thumbsup:
 
Thanks guys. That link is great...pics help a lot. I saved that whole page pics and all to my hard drive.

I found this too:

Test Cypionate 5 gram conversion

Needed
5 grams test c
1ml Benzyl Alcohol = 5% BA
15.25 ml sesame oil
Syringes 3cc & 5/10cc
18 or 20 gauge needles
mixing Vial
Sterile Vial
Whatman sterile filter


1. Weigh out 5 grams of powder.
2. Place powder in vial.
3. Add BA to the vial.
4. Heat oil in the oven to help sterilize it, heat to at least 212 degrees F. I usually heat my oil at 275 to be sure, I put the oil in a muffin pan, just fill one of the indentions this is plenty for these experiments. Also heat more oil than you need, as you will not be able to get it all out of the pan.
5. Add oil to the vial, save 2 ml of oil in the syringe for later. Gently shake vial.
6. Heat mixture if necessary. I like heating my powder products, by placing the vial in a frying pan, and placing it on the eye of the stove.
7. Place a 18 or 20 gauge needle in the sterile vial attach Whatman sterile filter.
8. Place another needle in the sterile vial to relieve the pressure.
9. Draw out solution with a syringe, run though Whatman filter.
10. Take other syringe with 2ml oil, run through Whatman into solution.

Invalid Link Removed
 
also ran across this site that has a half life calculator/list and detailed injection instructions. Formatting on this site was screwed up a little, but i just scrolled down and found the links to the miltipart injection procedures: Invalid Link Removed

Anyone with better info please post.
 
oh i'm not plannin on doing this for a few months...i have to knock my wife up again and i don't wanna mess up my nuts :)
 
Manu20 said:
Lol...Good luck with that. :thumbsup:
Click to expand...
thanks...it's alot of work ;)

this is our second and most likely last child so after that it's time for daddy to open up his gear box.
 
You must log in or register to reply here.
Back
Top