its simple.
Have all your items in front of you. (syringe, cotton balls, Vials)
Wash hands thoroughly. Follow up with some anti-bac purell if you wish. (or splash some rubbing alcohol onto your freshly washed hands)
Saturate a cotton swab with isopropyl alcohol. Rub the spot which you plan on injecting.
Do not let anything touch that spot. Dont fan it or blow on it to dry.
Saturate another cotton ball and place it ontop of the open bottle of alcohol. You'll need it for after youre done injecting.
Use a Q-tip dipped in alcohol to clean the vials rubber stopper. Dont blow on it, let it air dry. Let NOTHING touch it.
Take your syringe out. remove the needle section. Place it back into the wrapper. Do not allow it to roll around or make contact with anything unsterile.
Remove a larger gauge needle from the wrapper. Place that onto the syringe.
Shake you gear slightly. Draw back some air into the syringe, This makes withdrawing oil easier as it creates pressure in the vial. (note: do not remove the crimped alluminum seal from your vial. i did this once and the pressure from the air blew the stopper off and i lost $100 worth of tren)
Hold the vial upside down, inject syringe into the center of the vials stopper. Press the stopper and push the air in. Now draw back on the plunger to desired ML level.
Withdraw from vial.
Remove the large gauge needle from the syringe while holding the syringe upright (with the needle facing towards the ceiling)
Carefully take the smaller gauge needle from the wrapper (the one you first took off) and place it onto the syringe.
Push the oil up slowly to the top until no air bubbles ar visible. Flick the Syringe to allow the bubble to raise towards the surface (keep the syringe and needle facing up towards the ceiling)
You can allow a drop or two of the oil to trickle down the needle. Thats fine.
Hold the syringe like you would a dart. keep it parallel with the floor if that makes sense. Dont inject on an angle. A slight downward angle is fine.
Push the needle in a slow deliberate manner into your skin. Dont stab but go too slow either. Its gonna hurt a bit as the needle pricks through the skin, but its not terrible. You'll feel no pain going through the adipose layer. Then you'll feel a twinge when you hit the muscle. Dont be alarmed if the muscle Involuntarily "Jumps". It happens.
Just hold steady.
Some people allow a bit of the needle to still be visible, i bury that thing completely into the muscle.
Now, while holding the syringe steady so it doesnt move around, pull the plunger back slightly.
If you see blood, remove the syringe, change needles and start again. If you see bubbles, you're good. if you see nothing happening, youre good. Dont think because there arent bubbles that you need to keep pulling the plunger.
So, now that we are sure we arent injecting into a vein (or artery), slowly push the plunger while keeping the syringe steady and stable. You may feel some pain as the oil spreads the muscle fascia. Youre fine though.
Have your soaked cotton ball ready (soaked with alcohol that is) for when you remove the syringe.
In one motion, pull the needle out of your injection spot. Place the saturated cotton swab onto the spot. No need to massage or rub. Some do, i dont.
You may see a bit of blood. Sometimes it will drip or squirt out, other times there is nothing.
Hold the cotton ball for a few secs on the injection site. check to see if there is any blood still leaking or oozing. You should be fine at this point.
Take your used needles and put them back into the plastic caps. Throw it away. I personally take them outside and dump em in a public dumpster, id rather not have that sitting in my garbage can for days, nah mean?
There ya go, your first injection. You might have some pain the next day, and the following day...Hell, i felt it for 4 days after my first injection.
GICH!