Making Test Enanthate

  1. Making Test Enanthate


    This experiment will yield 100mls of test enanthate at 250mg/ml.

    Sorry bros, I forgot to take pictures of a few steps.

    Things needed:

    1 - 5ml syringe
    1 - 10-12ml syringe
    1 - 20ml syringe
    A few needles 18-23g
    Alcohol wipes or another way to help ensure sterility
    2 sterile 100ml vials (must be identical)
    5ml benzyl alcohol (BA)
    1 .22-.44 pore size sterile syringe filter
    25 grams testosterone enanthate powder
    1 - Small funnel
    Approx 75ml Sterile Oil
    Pen/marker that will write on glass
    Accurate scale
    Rubbing alcohol
    Duct tape


  2. Weigh out 25 grams of test enanthate. Notice that some of the powder is hardened as it melted a bit in my pocket and then hardened in cooler temp.
    Attached Images Attached Images  

  3. Take lid off of 100ml vial and fill with 100ml of rubbing alcohol using 20ml syringe. Once you have fininshed mark line where alcohol level is and dump out liquid. Put bottle in oven at 200 F and let liquid evaporate. Sorry no picture.
    •   
       


  4. Take funnel and pour powder into vial. Add 5ml of BA using 5ml syringe and put in pot of water on low till powder has completely turned into a liquid.
    Attached Images Attached Images  

  5. Take 20ml syringe and fill vial with oil until you are about a cm or so from the 100ml line you had previously marked on vial (not very accurate i know). As you can see, i duct taped the stopper on real good so that the vial can be turned upside down and not spill.
    Attached Images Attached Images  

  6. Put bottle back in pot on low heat for 10min or so and then shake to make sure product is completely mixed.

  7. Using 10-12ml syringe draw up oil using 18ga needle.
    Attached Images Attached Images  

  8. Wipe rubber stopper of second 100ml vial and put two 20ga needles through it. Attach whatman filter to syringe.
    Attached Images Attached Images  

  9. Put syringe filter into one of the needles that are in the 100ml vial.
    Attached Images Attached Images  

  10. Repeat procedure until bottle is finished, but leave whatman filter in sterile vial, just remove syringe to refill.
    Attached Images Attached Images  

  11. Once done with bottle, draw up 15ml or so of sterile oil. Grab empty bottle that has 100ml marking and put beside filtered bottle of gear. Flush filter with oil until the bottle matches the 100ml line of empty vial.
    Attached Images Attached Images  

  12. Apply heat or shake so that oil mixes in with the rest of your gear. Admire work.
    Attached Images Attached Images  

  13. There you have it, 100ml at 250mg/ml. May not have been the best way to do this but this was my first attempt at this and i think it turned out well. A couple of things i experienced that i should point out.
    I tried using 20ml syringe but 12ml one was much faster.
    I made eq the same way but filtered into 10 10ml bottles, I believe that using the 100ml vial was faster and more sterile than using 10 small bottles. Now all you have to do is draw gear up and inject 10ml into each bottle. Now go get huge!

  14. BRO! THANK YOU FOR THESE PROCEEDURE. YOU'RE THE BEST MAN!

  15. No prob bro, easy as hell to do.

  16. i guess getting test enthante powder in canada is no problem ?

  17. Originally posted by tommy_69
    i guess getting test enthante powder in canada is no problem ?
    Not for me so far

  18. I'd love to see the eq recipe.

  19. It is the exact same just use 20g of eq rather than 25g to give you 200mg/ml rather than 250mg/ml. I will post up another deca and test thread within the coming week or so. This time using a powder calculator.

  20. Originally posted by Kitchen Chemist
    Weigh out 25 grams of test enanthate. Notice that some of the powder is hardened as it melted a bit in my pocket and then hardened in cooler temp.
    sorry, dont you mean 2.5g?

  21. That recipe i posted was to make 100ml of test enanthate not 10ml but if you were making 10ml than 2.5g would be correct.

  22. ahhh ok, you mind if i ask what price range 25g of enth goes for, or is that against the rules?

  23. Sent you a pm.

  24. Originally posted by Kitchen Chemist
    It is the exact same just use 20g of eq rather than 25g to give you 200mg/ml rather than 250mg/ml. I will post up another deca and test thread within the coming week or so. This time using a powder calculator.
    Would that be using boldenolone base? I ask because I have an opportunity to get some. If not, would boldenolone base be usable?

    Thanks.

  25. You will not get bold base at 200mg/ml unless you come up with some funky combo of solvents, ba and bb will definately not do it.

    Try PEG-400, 5% BA and 15% PEG. You may have to use a glycerin with it rather than oil, but that should get it easily to 100mg/ml no prob.

  26. for entertainment purposes only right. you dont want to be labeled a source.
  

  
 

Similar Forum Threads

  1. Test enanthate is making me a bad man.
    By synergy7 in forum Anabolics
    Replies: 89
    Last Post: 08-02-2010, 12:25 PM
  2. Schering test enanthate
    By demon in forum Anabolics
    Replies: 0
    Last Post: 06-23-2004, 05:47 PM
  3. Test enanthate + trenbolone enanthate?
    By Johnblack in forum Anabolics
    Replies: 18
    Last Post: 06-05-2004, 09:09 PM
  4. 4AD vs. Test Enanthate
    By MF210 in forum Anabolics
    Replies: 12
    Last Post: 04-27-2004, 06:25 PM
  5. making test enanthate
    By broker_mike in forum Anabolics
    Replies: 10
    Last Post: 08-18-2003, 08:37 PM
Log in
Log in