Sterile Filtering Syno Powder

  1. New Member
    Brock Landers's Avatar
    Join Date
    Oct 2002
    Age
    36
    Posts
    162
    Rep Power
    230
    Level
    11
    Lv. Percent
    72.27%

    Sterile Filtering Syno Powder


    I just finished 5c's of a 10 c D**** Kit and I have a major problem!!!!!!
    I decided to form crystals using the drip method and came out with some great results. I followed the directions exactly and rinsed the powder numerous times in a painters mask. Anyways, once I allowed the powder to completely dry and broke apart the clumps into a fine powder, I added the powder to the oil/solvent mix. I wanted to make 150mg/ml and D advised me to remove the proper amount of oil and not add solvent. I cut the oil to 57 ml to get around 150mg/ml assuming a 20% loss factor. After I heated the oil and began to filter through the sterile filter, I could only get 10 ml through before the filter clogged. I ran the oil thrugh a coffee filter hoping to remove whatever was clogging the sterile filter. Then I heated the oil and attached a new sterile filter and repeated the process. Once again I clogged after 10 ml. So, I repeated the process of filtering with a coffee filter again. Same fricking result as I clogged a 3rd filter. Finally I was able to pass the remaining 20 ml or so through the last filter and finish with approxamately 50-52 ml.

    Needless to say I am pissed that it took 4 filters to get the job done, but I have no clue why this happened. I do fina conversions all the time and can get away with using 1 sterile filter for 4 grams even when making it at 150 mg/ml. Any help or input would be greatly appreciated. I do have a few filters left, but I dont want to use the all up on his final 5c conversion. Maybe I'm wrong but it seems absurd that it would take 4 filters to do 50 ml at 150mg/ml. Thanks for your help!

  2. The Axe Man Cometh!!
    ironviking's Avatar
    Join Date
    Dec 2002
    Posts
    401
    Rep Power
    346
    Level
    19
    Lv. Percent
    64.92%

    I had the same problem so I went with 100mg/ml, that seemed to work fine. Sorry but I have no advise for filtering any higher combo's.
  3. New Member
    Brock Landers's Avatar
    Join Date
    Oct 2002
    Age
    36
    Posts
    162
    Rep Power
    230
    Level
    11
    Lv. Percent
    72.27%

    hmmm......I have the all of the other kit left, ie oil, so maybe I will try that I guess for the last batch.........
    •   
       

  4. New Member
    prolangtum's Avatar
    Join Date
    Sep 2003
    Posts
    453
    Rep Power
    364
    Level
    17
    Lv. Percent
    40.53%

    I have had that problem with syno before, sometimes I can get 160mls through 2 filters, sometimes it take 6
  5. Brewing Anabolic Minds
    Chemo's Avatar
    Join Date
    Oct 2002
    Posts
    2,022
    Rep Power
    0
    Level
    29
    Lv. Percent
    27.95%
    Achievements Posting Pro

    Be sure to filter while the oil is still hot....
  6. New Member
    Brock Landers's Avatar
    Join Date
    Oct 2002
    Age
    36
    Posts
    162
    Rep Power
    230
    Level
    11
    Lv. Percent
    72.27%

    I nuked it for 40 sec, so I know it was hot, but I will go ahead and try again but this time at 100mg/ml....thanks for the responses
  7. Brewing Anabolic Minds
    Chemo's Avatar
    Join Date
    Oct 2002
    Posts
    2,022
    Rep Power
    0
    Level
    29
    Lv. Percent
    27.95%
    Achievements Posting Pro

    DON'T MICROWAVE THE GEAR!

    Place it in an oven at 250 degrees F for 15-20 minutes.

    Chemo
  8. New Member
    prolangtum's Avatar
    Join Date
    Sep 2003
    Posts
    453
    Rep Power
    364
    Level
    17
    Lv. Percent
    40.53%

    Chemo,
    Ive always wondered about that. What does microwaving gear do to the steroid molecules?
  9. Brewing Anabolic Minds
    Chemo's Avatar
    Join Date
    Oct 2002
    Posts
    2,022
    Rep Power
    0
    Level
    29
    Lv. Percent
    27.95%
    Achievements Posting Pro

    It excites certain functional groups such as -OH, -O, and to a small degree double bonds.

    In a typical recipe there will be the gear itself with BA and BB....all of which has active functional groups with microwave radiation. There may be a possibility of compromising the structural integrity of all.

    Chemo
  10. New Member
    Brock Landers's Avatar
    Join Date
    Oct 2002
    Age
    36
    Posts
    162
    Rep Power
    230
    Level
    11
    Lv. Percent
    72.27%

    post noted, thakns for the heads up!!!!
  11. New Member
    good_guye28's Avatar
    Join Date
    May 2003
    Age
    45
    Posts
    297
    Rep Power
    290
    Level
    17
    Lv. Percent
    10.53%

    chemo, you make me wish i had taken science more serious in school. your knowledge blows my mind.........

    i thank god people like you are around to help people like me with all their questions on this stuff. honestly i know id still be about 170lbs if it werent for this site....
  

  
 

Similar Forum Threads

  1. Replies: 5
    Last Post: 10-07-2011, 04:22 AM
  2. Effects of not filtering test prop powder
    By rombusempire in forum Anabolics
    Replies: 2
    Last Post: 10-04-2008, 12:58 PM
  3. Filtering method for syno conversion
    By mildain in forum Anabolics
    Replies: 2
    Last Post: 02-07-2006, 09:49 PM
  4. Drying syno powder
    By Bennett in forum Anabolics
    Replies: 6
    Last Post: 01-23-2005, 03:41 PM
  5. Ohh no some powder in the whatman filter ?!@
    By SeaHawk22 in forum Anabolics
    Replies: 1
    Last Post: 01-01-2005, 05:37 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Log in
Log in